Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
You must login to post a message.

11/25/2021 1:17 AM
JackedUp and CapnWhidbey, Welcome !

11/21/2021 1:56 AM
Welcome, pimaCanyon and Chris Porter!

11/18/2021 3:29 AM
locotoro, ionpau and gougege, welcome cup

11/16/2021 12:53 AM
RidgevilleRoaster OH, _lg3, Yirgaman, Houncer and AgressivStreetLamp
welcome !

11/15/2021 9:57 AM
Welcome, jasper_8137, goldyy9 and Evermancg !

In Memory Of Ginny

Latest Donations
JackH - 25.00
snwcmpr - 10.00
Anonymous - 2.00
Anonymous - 5.00
Anonymous - 5.00
Users Online
Guests Online: 25

Members Online: 0

Total Members: 7,359
Newest Member: JackedUp

View Thread

Who is here? 1 guest(s)
 Print Thread
HG/BM and pre heating...
Cory Nielsen
I have read a lot about people pre heating their roasters prior to dropping the beans into the roaster, my question is, with a HG/BM set up should this be done?

Right now my set up is just a standard BM rewired to constant agitation, with a heat gun stuffed down the top, I haven't had any issues getting to SC in under 15 min starting cold. (I have sacrificed some beans in the name of learning my roasters performance arc)
I just don't know if preheating effects the flavor of the beans. Should I pre heat? If so what is the target temp for the pre heat?

In a HG/BM should the roast times be a lot faster then 15 min?

Thanks in advance for any help!

I imagine it's not very effective to preheat for HG/BM since the heat source is direct-blown as well as the fact that opening the bread machine will release 90% of the heat energy and doing so would lose any preheating benefits you might otherwise gain from fully enclosed setups like drum roasters using radiant heat.
Edited by weenie_roaster on 06/05/2014 10:30 PM
I preheat mine, though I've not been roasting long, nor have I tried not preheating. I do have insulation in the form of a fire blanket rapped around the roasting chamber to give it some heat retention. My pre bean drop routine goes like this;
Set HG to around 130DegC at put it in the roasting position while I set up everything else around it.
Now that the thermocouple and software is running I tweak till RoR is flat around 110DegC.
My BM is still stockish, so I have to wait for 3mins till the paddle is fully turning.
With 30secs to go, I remove the HG and set it to the desired starting temp then wait for the BT probe to drop to 100DegC.
Then I drop the beans and add the HG back.
The tipping point is around the 70DegC mark with this preheat. So I'd say it is helping me. I haven't noticed any tipping of the beans either.
Hi Cory

Don't get too obsessed with a preheat for hg/bm. Turn it on and preheat for a minute or two if you get the chance but it's not critical. As far as roast time 15 is a little long but not horrible. I've found that for a base profile about 12 minutes is good - drop to 300F in 4 minutes; 300F to 400F in 4 minutes; 400F to finish in 4 minutes. - a little longer for darker fc+ espresso roasts but not much. Hopefully that's right from memory!
Honey badger 1k, Bunn LPG-2E, Technivorm, Cimbali Max Hybrid, Vibiemme Double Domo V3
Mad Mac
jaywoo, what is a cement sheet?
Edited by Mad Mac on 10/30/2014 4:36 AM
Fibre-cement sheet is another name for it. Sounds like you have found my BM/HG build photos on Flickr. Cement sheet has good thermal properties for it thickness, which is why I used it. In between the cement sheet top and the roasting chamber is a sheet of stainless steel that I cut out of an old clothes dryer. This also forms the exhaust port.
Mad Mac
I wanted to exhaust the internet first before i ask to be considerate.

Nice design. I do believe they sell fiber cement here. On its own, does fiber cement react to the roasting heat?
I'm not 100% sure but I'm going to say no. The sheet of stainless steel was also intended to form a barrier between the fiber cement and the roasting beans.
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
Heating Issues with Nesco Pro Other Roasters 5 04/22/2021 1:51 PM
Quest Conversion to Induction Heating Idea Building a Coffee Roaster 7 02/01/2021 11:35 AM
Heating Element Control Electric and Gas Heat Sources 9 01/05/2021 7:55 PM
Heating Element Failure -- help? Electric and Gas Heat Sources 6 12/10/2020 6:40 PM
Heating Coil Melting Connector Insulation Electric and Gas Heat Sources 3 11/23/2020 7:57 AM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion Copyright © 2021 PHP-Fusion Inc
Released as free software without warranties under GNU Affero GPL v3
Designed with by NetriX