Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.

Shoutbox

You must login to post a message.

NetriX

09/28/2020 9:48 AM

Working on site improvements, bare with me.

renatoa

09/28/2020 8:58 AM

Where are the old themes ?!!!

NetriX

09/28/2020 12:46 AM

Made some changes, shoutbox was working without verification.

JackH

09/27/2020 2:53 PM

A lot of shoutbox spam attacks lately.

Koffee Kosmo

08/28/2020 7:15 PM

I have updated my signature and added links to the KKTO roaster build

Shoutbox Archive

Forum Threads

Newest Threads

TC4+ Arduino coffee ...
Coaxing berry flavor...
Finding first princi...
Fluidbed Roaster pro...
DASH Popper - Workin...

Hottest Threads

TC4+ Arduino coff...	[218]
Transparent Fluid...	[120]
Fluidbed Roaster ...	[81]
1 lb drum build	[50]
Rotisserie Toaste...	[26]

Users Online

Guests Online: 3

Members Online: 1
JackH

Total Members: 6,749
Newest Member: Ivanwrowl

In Memory Of Ginny

Donations

Donations Bank

Latest Donations
Anonymous - 5.00
Anonymous - 5.00
renatoa - 2.00
JitterzZ - 2.01
renatoa - 2.00

Oh no! Where's the JavaScript?
Your Web browser does not have JavaScript enabled or does not support JavaScript. Please enable JavaScript on your Web browser to properly view this Web site,
or upgrade to a Web browser that does support JavaScript; Firefox, Safari, Opera, Chrome or a version of Internet Explorer newer then version 6.

View Thread

Homeroasters - Home Roasting Coffee Community » ALL ABOUT ROASTERS » Quest M3 Roaster

Who is here? 1 guest(s)

Quest Fan Control and Wiring in General
Nunas	#1 Posted on 06/11/2015 10:41 AM
Newbie Posts: 11 Joined: November 09, 2012 Location: Osoyoos Cottages BC Canada	The instructions for the Quest M3 mention calibrating the fan control, so as to know where the lowest speed is. If I understand correctly, from full CCW through some of the control's rotation the fan does not run, then it begins to run at some point as the control is turned more CW. The fan on my M3 always turns. At no point of rotation of the control does it stop. Of course, as I turn it CW, it runs faster. Does anyone know anything about this? Did the original M3s act differently than the newer ones in this regard? Mine is a 2013 build. While I realise I can stop the air flow by opening the cooling door, I'd like to have a position where the fan is off and can probably do this by changing the potentiometer for one with an integral on/off switch, or by changing a component in the controller. I'd rather not reinvent the wheel, but the one thing I've not seen is a wiring diagram. Does anyone have one to share? Failing an official diagram, has anyone taken their Quest apart and drawn one? A decent diagram might come in handy down the road if something goes wrong. Roasters: Quest M3, Freshroast SR500 & SR700 Grinders: Baratza Preciso+Esatto, Breville BCG450, Zassenhaus Havana Brewers: Magister Stella Pro, Bodum Chambord, Aero Press, Chemex CM-8A, Nissan Plunger, Yama SY8
	Web

Nunas	#2 Posted on 06/30/2015 2:21 PM
Newbie Posts: 11 Joined: November 09, 2012 Location: Osoyoos Cottages BC Canada	I took my M3 (2013 model, 120-Volt) apart and traced the wiring. Please PM me if anyone sees any errors. Nunas attached the following image: Edited by Nunas on 06/30/2015 2:33 PM Roasters: Quest M3, Freshroast SR500 & SR700 Grinders: Baratza Preciso+Esatto, Breville BCG450, Zassenhaus Havana Brewers: Magister Stella Pro, Bodum Chambord, Aero Press, Chemex CM-8A, Nissan Plunger, Yama SY8
	Web

Jump to Forum:

Similar Threads

Thread	Forum	Replies	Last Post
Troubleshooting Hottop with TC4 +HTC fan control	HotTop Roaster	1	09/20/2020 12:23 PM
Wiring Diagram Check	Fluidbed Roaster	31	08/30/2020 4:15 PM
Gas Control advise needed	Drum Roasters	18	03/02/2020 4:33 PM
Question about wiring a dryer element	Fluidbed Roaster	5	02/04/2020 5:04 PM
West Bend Poppery I Fan Boost Wiring	Popcorn Popper roasting	15	01/16/2020 2:02 AM