Skywalker roaster... | [297] |
Skywalker, the AL... | [214] |
Skywalker Roasts | [94] |
Rainfrog's Roastm... | [54] |
War on Farmers by... | [40] |
BMHG mod question
|
|
BeefTips |
Posted on 04/09/2018 9:20 PM
|
Newbie Posts: 25 Joined: March 29, 2018 |
So I'm going to start my build soon and I've been reading and reading and reading here. There is so much knowledge it's hard to decipher what is a must and what is there to make it better. I'm on a budget so I don't want to go crazy with my first build. I simply want a good consistent roaster. What mods should be on my to do list. I know I'm going to rewire and remove the teflon. From there what should be my focus? Better insulation? Better lid seal? Exhaust? I have a regal bread maker that I'll attach a pic of. Any advice is greatly appreciated.
BeefTips attached the following image:
|
|
|
BeefTips |
Posted on 05/17/2018 12:38 PM
|
Newbie Posts: 25 Joined: March 29, 2018 |
So I finally completed my initial build. I rewired and added a plug in. I made a stainless lid with a high density board on bottom to retain heat. Removed the tephlon from the roasting chamber. I mounted a brass tube to allow a convenient place to put my temp probe. |
|
|
greencardigan |
Posted on 05/17/2018 8:53 PM
|
1 1/2 Pounder Posts: 1185 Joined: November 21, 2010 |
Great! Have you done any roasts yet? Are you going to manually control the heat gun? |
|
|
BeefTips |
Posted on 05/24/2018 12:52 PM
|
Newbie Posts: 25 Joined: March 29, 2018 |
Done my third roast last night. 1st roast too light. 2nd was a great medium roast. 3rd ran into issues. My kid has a hole just big enough for the HG ro stand in so I set in the lid right and then I adjust the heat on it as necessary. |
|
|
Husamka |
Posted on 05/26/2018 6:42 PM
|
1/4 Pounder Posts: 56 Joined: September 16, 2016 |
Good start, Can we see how you mounted the brass tube and the probe ? also how you attach the heat gun to the machine. |
|
|
BeefTips |
Posted on 06/02/2018 9:44 AM
|
Newbie Posts: 25 Joined: March 29, 2018 |
Here is what it all looks like as of right now, The HG isnt attached; it fits in the hole in the lid and supports itself. The tube is secured with some extra copper i had laying around. Its low enough for the probe to be in the beans whether im roasting a half pound or a whole pound.
BeefTips attached the following images:
|
|
|
Husamka |
Posted on 06/02/2018 2:27 PM
|
1/4 Pounder Posts: 56 Joined: September 16, 2016 |
Practical setup. This heavy lid allow to hold the Heat Gun which a lot of people need stand to hold it. |
|
|
BeefTips |
Posted on 06/02/2018 2:33 PM
|
Newbie Posts: 25 Joined: March 29, 2018 |
Yes it is pretty heavy. Still not decided as to whether or not I'm going to add the exhaust. |
|
|
Koffee Kosmo |
Posted on 06/03/2018 12:42 AM
|
Administrator Posts: 1620 Joined: December 31, 2008 |
If you want to add an exhaust then the best one for your setup is something like a Webber BBQ on the lid It?s adjustable and easy to do https://i.ytimg.c...efault.jpg KK I home roast and I like it. Designer of the KKTO
Roaster Build information https://homeroast...ad_id=1142 https://docs.goog...lide=id.i0 Blog - http://koffeekosm...gspot.com/ Bezzera Strega, Mazzer Robur Grinder, Pullman Tamper Convex, (KKTO) Turbo Oven Home Roaster. |
|
|
BeefTips |
Posted on 06/03/2018 7:44 AM
|
Newbie Posts: 25 Joined: March 29, 2018 |
I was thinking about something like that. I have extra metal I made the lid out of. I can just cut out another hole same as the one for my hg and them cut out a circle piece of metal to cover it. |
|
|
jkoll42 |
Posted on 06/23/2018 2:35 PM
|
1 1/2 Pounder Posts: 860 Joined: February 14, 2011 |
Hey Beef - you're going down a really good path on the HGBM. The cost for batch weight ratio is so good and it's a very repeatable platform. I did a ton of mods and trials and thread below really was the most stripped down and inexpensive end result. Any questions just ask. https://forum.hom...ad_id=2427 -Jon
Honey badger 1k, Bunn LPG-2E, Technivorm, Cimbali Max Hybrid, Vibiemme Double Domo V3 |
|
|
BeefTips |
Posted on 06/25/2018 6:42 AM
|
Newbie Posts: 25 Joined: March 29, 2018 |
Thanks jkoll |
|
Jump to Forum: |
Thread | Forum | Replies | Last Post |
---|---|---|---|
Pressure gauge question | Drum Roaster (Store Bought and Commercial) | 2 | 01/18/2024 8:03 PM |
Solid State Relay Question | Dataloggers/Controllers/Rate of Rise Meters | 11 | 11/27/2023 9:16 AM |
Artisan virtual device question | Dataloggers/Controllers/Rate of Rise Meters | 1 | 08/23/2022 9:50 AM |
Question about TC4 ambient temperature/cold junction MCP3424/MCP9800 | Dataloggers/Controllers/Rate of Rise Meters | 5 | 03/27/2021 9:28 AM |
Behmor 1600 question | Roasting Coffee | 11 | 03/15/2021 12:32 PM |