TC4 with aArtisan... | [423] |
Air Popper Heater | [34] |
Both Manual and D... | [25] |
Can First Crack b... | [14] |
Using a ring (reg... | [13] |
Overheat / shutoff safety on bread maker
|
|
CoffeeAndKimuras |
Posted on 08/16/2018 7:34 PM
|
![]() Newbie ![]() Posts: 13 Joined: July 30, 2018 |
Hey all, I was about 12' into my roast on newly built corretto roaster and it was going great...until my bread maker flashed "E01", shut off, and wouldnt turn back on. My bread maker is an Oster. After some research I quickly discovered that the E01 warning is an emergency failsafe / shut off for overheating the unit. Has anyone ever experienced this and do you have any work arounds for it? I do still have the heating element connected...idk if theyre related and that would fix it? Thanks for your help |
|
|
JackH |
Posted on 08/17/2018 9:00 AM
|
![]() Administrator ![]() Posts: 1809 Joined: May 10, 2011 |
Most consumer products with heaters/heating coils and motors have a fire safety fuse (thermal fuse). It is usually connected in series with the heating coil or attached to the case of a motor. I have seen them in roasters and coffee grinders. Not sure where yours is exactly but it may look like a metal cylinder. Once these blow, they can't be reset without replacement. I believe they are rated in temperature. ![]()
JackH attached the following image:
---Jack
KKTO Roaster. |
|
|
ChicagoJohn |
Posted on 08/17/2018 9:56 AM
|
![]() Pounder ![]() Posts: 511 Joined: June 15, 2015 |
Quote JackH wrote: Most consumer products with heaters/heating coils and motors have a fire safety fuse (thermal fuse). It is usually connected in series with the heating coil or attached to the case of a motor. I have seen them in roasters and coffee grinders. Not sure where yours is exactly but it may look like a metal cylinder. Once these blow, they can't be reset without replacement. I believe they are rated in temperature. Resettable fuses are also used quite often -- when you wait about 30 minutes for the appliance to cool down, they reset and function normally again. And as you say, they come in a wide range of set points. I had one on the vacuum motor assembly I used in my air roaster and replaced it with a higher value. But before you do this, it's a good idea to take a close look at the materials used and consider what they are actually capable of withstanding. So many beans; so little time.... |
|
|
CoffeeAndKimuras |
Posted on 08/18/2018 11:04 AM
|
![]() Newbie ![]() Posts: 13 Joined: July 30, 2018 |
https://imgur.com... Is this the temperature sensor for the failsafe? Would it be possible to just relocate this away from the bread pan or outside the BM to keep it from reading high and shutting off? Quote JackH wrote: Most consumer products with heaters/heating coils and motors have a fire safety fuse (thermal fuse). It is usually connected in series with the heating coil or attached to the case of a motor. I have seen them in roasters and coffee grinders. Not sure where yours is exactly but it may look like a metal cylinder. Once these blow, they can't be reset without replacement. I believe they are rated in temperature. ![]() Edited by JackH on 08/18/2018 3:44 PM |
|
|
BenKeith |
Posted on 08/18/2018 3:42 PM
|
![]() Pounder ![]() Posts: 485 Joined: April 21, 2014 |
Since a bread machine was never intended to be used at the temps required for roasting coffee, you will probably have to bypass the sensor, it's just going to blow it again if you replace it with a like one. To keep this device you will need to go to one of a higher temp rating. Probably something in the 700+ degree range to keep it from regularly blowing. They are also usually spot welded onto the wires so that may create a problem for you also. Regular solder will melt at your working temps. You can silver solder them but you will need to heat sink the sensor very well. Most silver solders require more heat than the device is rated for. To do away with it, just put a solid wire between the two points the wires connected to the sensor. |
|
|
CoffeeAndKimuras |
Posted on 08/19/2018 8:29 AM
|
![]() Newbie ![]() Posts: 13 Joined: July 30, 2018 |
for the time being I have just taken the sensor off of the breadpan and lead the wires outside so that it doesnt overheat. this seems to have done the trick...for as long as it lasts. |
|
|
jackofalltrades |
Posted on 04/02/2019 4:34 AM
|
![]() Newbie ![]() Posts: 2 Joined: April 02, 2019 |
Which model of Oster bread maker are you using? I am using the Oster machine, too, mine is the 2-Pound Expressbake Bread Machine. It works good for me so far since I bought it last December. |
|
Jump to Forum: |
Thread | Forum | Replies | Last Post |
---|---|---|---|
Espresso maker under 100$ | ALL ABOUT ESPRESSO MACHINES | 24 | 04/04/2022 12:25 AM |
Bread Maker Recommendations For Roasting Beans | Heat Gun Roasting | 9 | 01/18/2022 9:54 AM |
Gas safety valve questions | Building a Coffee Roaster | 6 | 07/24/2021 9:46 AM |
Heat gun bread machine roaster--how can I change container? | Heat Gun Roasting | 8 | 03/05/2021 4:14 PM |
Help with Oster Bread Machine | Bread Machine Roasters | 1 | 05/27/2020 3:02 PM |