topbanner.gif
Login
Username

Password




Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Shoutbox
You must login to post a message.

renatoa
08/10/2022 1:56 AM
nguyencoffeesupply
and RoyB, Welcome

renatoa
08/06/2022 1:31 PM
Welcome, oak202, CoffeeNutZ and Mlcharlestonsc

Strangeworth
08/04/2022 9:34 PM
Thank you!

renatoa
08/03/2022 2:09 AM
Strangeworth and BigPalm, welcome to forum

Tamesino
08/02/2022 12:01 PM
Thank you guys and gals !! Exited to be here greenman

In Memory Of Ginny
Donations

Latest Donations
dmccallum - 10.00
JackH - 25.00
snwcmpr - 10.00
Anonymous - 2.00
Anonymous - 5.00
Users Online
Guests Online: 13

Members Online: 0

Total Members: 7,627
Newest Member: nguyencoffeesupply

View Thread

Who is here? 1 guest(s)
 Print Thread
Understanding the Curve
CK
Are there any roasters who want to share their experiences with profile roasting?

This curve is open to discussion on how to make a better tasting coffee. What would you do to adjust this profile to improve or change the end flavour? As it is, it's pretty nice when brewed as a filter coffee... this roast had berry and dark chocolate notes for about 2 weeks before starting to fade.

The new hot air drum machine I'm using is very nimble with low thermal inertia and can be controlled like a fluidbed... Does anyone have suggestions on what could make this coffee sweeter, more complex, etc?
CK attached the following image:
guji_shakiso_ornat_de400fc848dr1119_354322_208c_143_21-12-19_1554.png

Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
allenb
Have you posted photos of your convection style drum roaster? I'd love to take a look at it.

One thing I would try is stretch end of drying by one minute. Second thing is to reduce time from 1st crack to end of roast by a minute. This seems counter intuitive since many suggest stretching this phase to increase sweetness but with some coffees, it's just the opposite. Worth giving each of these a try one at a time.
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
renatoa
Short drying is probably due about the high charge and start power level, this is the most intriguing part of this roast approach.

For my mixed convection/radiant machine, done using a TO as heater, the preheat to 170+/-10 degrees stabilize at a power value in the 30-40% ballpark.
Here I see the first point that make me wonder... why only 144C at charge, when the power is at 75%... then next minute, with almost no change in power you reach 200C ET, performance that I was capable only with a FB design.
The only answer I can give to myself is that you charge without waiting heat stabilize. Probably when you see 150 or so on the increasing temperature ramp, you push the charge lever.

More on power management handling on my machine, that replicate the routine I seen on others.
The power level of preheat is keep unchanged the first 30 seconds of charge, (soaking) then start increase slowly until TP, about minute 1, then increase faster, reaching 70-75% in the minute 3. So at minute 3 our machines have similar power levels, but 200C ET is touched later on mine, about minute 4-6, compared to yours, almost fluid bed dynamics, as you specified...

DE happens about minute 5 for me.

Back to thread subject: will this drying approach influence the taste?
No idea... just try and see if a milder power curve for drying make a difference.
For mine, charging at 75% will led to roast defects, too much heat too fast.
That's because 75% for me means more than 250C, if let machine stabilize, which is too much heat to attack the greens.

Agree with Allen to short the development, try next roast under 2 minutes, or 15-20% DTR
The flattening of RoR at FCe, 10:19, it's a sign you should cut there, for my roasts there is no development past FC end.
 
CK

Quote

allenb wrote:

Have you posted photos of your convection style drum roaster? I'd love to take a look at it.

No, nothing posted anywhere yet. Perhaps in the near future this roaster design will be shared...

Quote

allenb wrote:

One thing I would try is stretch end of drying by one minute. Second thing is to reduce time from 1st crack to end of roast by a minute. This seems counter intuitive since many suggest stretching this phase to increase sweetness but with some coffees, it's just the opposite. Worth giving each of these a try one at a time.

Thanks for the comments Allen, I'll run a roast with the suggestion and report back or post results. I am concerned about dropping 1 minute earlier because the bean temperature at drop will be lower than I'm used to... Maybe it will be a pleasant fruity surprise.
Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
CK

Quote

renatoa wrote:

Short drying is probably due about the high charge and start power level, this is the most intriguing part of this roast approach.

I'm still learning to drive this machine.

Quote

renatoa wrote:
Here I see the first point that make me wonder... why only 144C at charge, when the power is at 75%... then next minute, with almost no change in power you reach 200C ET, performance that I was capable only with a FB design.

This machine at it's heart is a FB design. That is why the TC response is fast and immediate on the profile. When charging with 680 grams greens, a fast temperature increase is needed to make the profile achievable in 12-14 minutes. With more greens at charge, the more initial heat required to meet the time markers.

Quote

renatoa wrote:
DE happens about minute 5 for me.

Agree with Allen to short the development, try next roast under 2 minutes, or 15-20% DTR
The flattening of RoR at FCe, 10:19, it's a sign you should cut there, for my roasts there is no development past FC end.

I'll change the power settings for charge and stretch the DE to about 5+ minutes and drop as suggested... stay tuned for the results.Grin
Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
renatoa
However... if this machine has indeed a FB heart and soul, I mean convection on steroids, then maybe we should change our minds and treat as a FB, with shorter times for all phases... thinking to something as in the attached image
...
renatoa attached the following image:
1216_cc_fb_pons_kp5_2_ki0_final.png
 
CK

Quote

renatoa wrote:

However... if this machine has indeed a FB heart and soul, I mean convection on steroids, then maybe we should change our minds and treat as a FB, with shorter times for all phases... thinking to something as in the attached image
...


Thanks Renato,
The times are relevant to the machine's design, power, and heat transfer potential to the beans. It's more efficient than a FB, but like all machines, it has limitations and preferred sweet spots. With a lower green bean charge weight or increased roast chamber temperature, yes it could be possible to shorten the curve.

In my posted curve you see a 680 grams charge being roasted with max power capped at 82% (1600w x 0.82 = 1312 x 2 heaters = 2624w). I try keeping the MET 250C or less. This profile works similarly for 908 grams charge, but I'm practicing using 680 until I learn the response of the machine.

I'll adjust the profile as mentioned and report back on the results... Understanding the Curve.
Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
allenb
Renatoa makes a good point on possibly needing a totally different approach if your roaster is fully convection but this depends on if you are using a wire or perforated drum with very little thermal mass and 90% of the heat transfer being delivered solely by air to bean and not air to solid drum and traveling back around through the back plate to the beans.

If this is the case and you do end up having the needed headroom in the power department then definitely experiment with the shorter profiles as renatoa mentioned.

As far as the often mentioned best practice max recommended ET of 260 c (500 F), don't worry about exceeding this temperature. Most large commercial fluidbed roasters regularly hit the 290s with no roasting defects at all and remarkable cupping scores.
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
CK
Here is one of two roasts completed today with a new power profile. No PID, just a natural power curve as Renato often mentions.ThumbsUp
I didn't quite get the recommended times, but the next round should be better... it'll be trial and error to get the power settings just right and learn the thermal characteristics of the machine, but it does look promising. The roasts today were shorter as intended, but with a slightly higher drop temperature. The beans retained about 1% extra moisture and goodness inside compared to the longer roasts of 12+ minutes. Looking forward to trying them in about 5 days...
CK attached the following image:
abyssinia_mocha_680g_423622_de417fc755dr1006_212c_118_22-01-17_1636.png

Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
renatoa
This is a curve I like !
Still too long development, for me, especially with that high average RoR, but depends on your taste, how acid/chocolate balance you prefer.
Seen such high RoR values at FC in nordic roasts only, but they have very short dev times, about one minute, to compensate the higher energy. But the nordic shool roasts have very different goals than what most people defines as "coffee" :)
Next roast I would keep the first phase, but lower the heat at the end, to have about 7 RoR when entering FC, and an average close to 5 for the Dev phase. And development shorter than 2 min/20%

I am cupping mine next three hours after roast, definitely same day.
You are losing flavors waiting so long, I feel them gone since day three.
Drinking mainly brew though...

Very good progress, bravo !
Edited by renatoa on 01/18/2022 2:35 AM
 
allenb

Quote

Next roast I would keep the first phase, but lower the heat at the end, to have about 7 RoR when entering FC, and an average close to 5 for the Dev phase. And development shorter than 2 min/20%


CK, what was the outcome of this roast? Very light, light, medium or darker than medium?

If very light, then there will be no way to stay under 2 min development and at the same time reduce RoR.
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
CK

Quote

allenb wrote:
CK, what was the outcome of this roast? Very light, light, medium or darker than medium?

If very light, then there will be no way to stay under 2 min development and at the same time reduce RoR.

For me, it is a medium roast. Today, day 3, it has a prominent cocoa flavour, low acidity, low sweetness, med-full body with a syrupy long hanging finish on the palate...

Here is an image of the results. (Please keep in mind that colour rendition of photographs from white balance settings, lighting, and your monitor's colour calibration, may cause the image to appear off.)
CK attached the following image:
coffee_image.jpg

Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
renatoa
Now is probably too late, but weight loss of the roast tell me some additional things to the color and other sensory hints.
Medium is when the loss is about 14%. Light is in the 12% ballpark.
 
louca
But isn't weight loss somewhat dependent on the starting moisture content of the bean? Or not? I really wanna know.
——————————
Behmor 2000AB+, OXO grinder, Escali L-600 scale, Clever Dripper and V60-02.
"I feel more like I do now than I did when I got here."
 
renatoa
Yes, it is, the numbers above are for well stored green, in the first year of crop.
I.e. about 10-11% moisture.
You can read in the literature about higher figures, like 12%, but this is really fresh crop... the first three months after import, which usually aren't available to us.
If this is really important, you can buy a moisture meter, about $200, or ask the seller, if he can measure this for you, just before packing.
 
CK
Here is a 10x recording of the Artisan workflow for the above roast in post #9. It was the second roast, back to back, so the machine carried more thermal inertia into this batch. The previous roast data is seen in the title because I hadn't changed it yet, so you see the first roast on this profile was dropped at 10m22s at 210C, whereas this one finished at 10m6s and 212C.


Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
CK
Here's a modified power profile that tries to get better numbers... I actually ran 2 batches back to back, and below are the resultant curves individually, and also how they look when overlaid one over the other.

I've cupped both these today (rested 4 days) and the flavour is wonderful. I describe it as a third-wave style light roast, clean with light fruity acidity, chocolate, long finish with a creamy velvet-like body... prepared using an Aeropress.

Thank you for the advice to make the adjustments that yielded good results. Grin
CK attached the following images:
guji_shakiso_1.jpg guji_shakiso_2.jpg guji_shakiso_1_and_2_overlay.jpg

Edited by CK on 02/02/2022 8:52 PM
Technivorm Moccamaster, Breville SGP, Transparent Roaster, Roaster908
 
allenb
Great to hear the new profiles are yielding good results! Obviously there's no one size fits all with all of the different green variables but hopefully the basic new shape will only need some small tweaks to be useful for everything you'll be roasting.
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
How drum mass affects the roast curve Drum Roasters 11 09/12/2021 5:08 PM
Natural bean curve with air roaster Roasting Coffee 17 06/07/2016 8:20 PM
Understanding the roast process HotTop Roaster 7 10/06/2013 8:31 AM
Toward a Unified Understanding of Roast Development for Sweetness Roasting Coffee 13 09/26/2013 6:30 PM
Drying Phase Curve Roasting Coffee 72 07/28/2013 11:47 PM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion Copyright © 2022 PHP-Fusion Inc
Released as free software without warranties under GNU Affero GPL v3
Designed with by NetriX