Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.

Shoutbox

You must login to post a message.

renatoa

08/10/2022 1:56 AM

nguyencoffeesupply
and RoyB,

renatoa

08/06/2022 1:31 PM

Welcome, oak202, CoffeeNutZ and Mlcharlestonsc

Strangeworth

08/04/2022 9:34 PM

Thank you!

renatoa

08/03/2022 2:09 AM

Strangeworth and BigPalm,

Tamesino

08/02/2022 12:01 PM

Thank you guys and gals !! Exited to be here

Shoutbox Archive

Forum Threads

Newest Threads

My 1-2 KG drum roaster
Air Popper Heater
Can First Crack be d...
Hello From Southern ...
Signal cable lengths...

Hottest Threads

TC4 with aArtisan...	[423]
Air Popper Heater	[34]
Both Manual and D...	[25]
Can First Crack b...	[14]
Using a ring (reg...	[13]

In Memory Of Ginny

Donations

Latest Donations
dmccallum - 10.00
JackH - 25.00
snwcmpr - 10.00
Anonymous - 2.00
Anonymous - 5.00

Users Online

Guests Online: 7

Members Online: 0

Total Members: 7,627
Newest Member: nguyencoffeesupply

Oh no! Where's the JavaScript?
Your Web browser does not have JavaScript enabled or does not support JavaScript. Please enable JavaScript on your Web browser to properly view this Web site,
or upgrade to a Web browser that does support JavaScript; Firefox, Safari, Opera, Chrome or a version of Internet Explorer newer then version 6.

View Thread

Homeroasters - Home Roasting Coffee Community » DATALOGGERS - CONTROLLERS - RATE OF RISE METERS » Dataloggers/Controllers/Rate of Rise Meters

Who is here? 1 guest(s)

Signal cable lengths to / fro to Arduino / TC4+
progen	#1 Posted on 08/04/2022 12:55 PM
Newbie Posts: 41 Joined: December 17, 2019	My current configuration is a 2.5m 3 core (w shield) 24AWG data transmission cable from the pot to A0 on the Arduino / TC4+ and then 25cm from OT1 to the SSR. Works perfectly. However, I was thinking of moving the Arduino / TC4+ to just beside my laptop and then using 2 of the cores of the 24AWG data transmission cable for the signal from OT1 to the SSR instead. Pot will then be connected with a 20cm cable to the Arduino / TC4+. The reason is because I personally like being able to see whether the TC4+ is behaving itself and communicating properly with the SSR whereas I can't see the two boards if they're mounted far from the laptop as originally planned. Is the Arduino's 5V or the TC4+'s OT1 stronger? Or is 2.5m still not long enough to worry about signal losses or interference?


renatoa	#2 Posted on 08/04/2022 1:30 PM
Administrator Posts: 2212 Joined: September 30, 2016	Interference depends on circuit impedance and wire length. OT1/SSR circuit is low impendance, versus the pot, which is higher impedance. Signals strength is similar for both, in the 0-5V range. OT1/SSR circuit signals are digital, so almost immune to interference, vs the analog signal of a pot. As a result of the above, OT1/SSR circuit is more appropriate to be remoted than the pot.


progen	#3 Posted on 08/04/2022 1:32 PM
Newbie Posts: 41 Joined: December 17, 2019	PERFECT! I'll shift the Arduino / TC4+ to the control panel then.

Jump to Forum:

Similar Threads

Thread	Forum	Replies	Last Post
TC4+ Arduino coffee roaster shield (TC4-compatible)	Dataloggers/Controllers/Rate of Rise Meters	247	05/18/2022 1:38 PM
TC4 Arduino could not set [email protected] 5357	Dataloggers/Controllers/Rate of Rise Meters	3	01/25/2022 6:13 PM
Testing Arduino UNO with bitwisetech / popc and MAX6675	Popcorn Popper roasting	70	12/05/2021 8:31 AM
SOLVED: Artisan says: "Arduino could not set channels"	Dataloggers/Controllers/Rate of Rise Meters	9	01/24/2021 2:14 AM
Arduino and Artisan	Dataloggers/Controllers/Rate of Rise Meters	4	01/21/2021 1:07 PM