Skywalker, the AL... | [263] |
War on Farmers by... | [53] |
Green coffee reviews | [10] |
Help and recommen... | [10] |
Skywalker roaster mods
|
|
sloppyjosh |
Posted on 12/03/2023 2:21 AM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
I've been doing a lot of work on this roaster. I've analyzed the communications between the roster and the controller, I can read the state of the heater, fan, and cooling fan, I'm really close on reading temperatures... I can read the data but having some issues converting it to temperature.. once I get that nailed down I should be able to pipe the data into Artisan for logging. Happy to share any details about what I've learned about the roaster or even the data sets I've collected if anyone is interested. |
|
|
renatoa |
Posted on 12/03/2023 3:24 AM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
Wow ! sure, post here all you are happy to share. Once the protocol is known, translating into a TC4 packet is easy, and available over USB for any external application for logging and archiving. Do you have an USB sniffing dongle, or what spy method are you using? Does the protocol offer a method to (over)write values on the display panel ? Asking because the RoR is too slow, at this rate can't be used for decisions for control in manual mode... would be nice to have a faster refresh rate. |
|
|
sloppyjosh |
Posted on 12/03/2023 9:32 AM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Here's how the roaster works from a control point of view. All the brains are in the controller. When power is applied (that is.. when it's plugged in) both the roaster and the control panel start sending a stream of data. They're always doing this even when the controller isn't on. There is no back and forth communication protocol or anything.. just each device streaming a message to the other. The controller connects to the roaster with a standard USB plug, however the manufacture is only using this plug for convenience. There is no USB communications going on. I soldered wires to the RX, TX, and Ground of the controller board. So I can plug those in to my logic analyzer or an arduino to sniff the data. The roaster simply does whatever the controller says to do. Attached is an example of what the data looks like on the wire. The orange trace is 7 bytes from the roaster -> controller, the white trace is 6 bytes controller -> roaster. You can see the message preamble (the large gaps) then when the signal goes low, if it's low for roughly 625 microseconds it's a binary 0, if it's low for 1500 microseconds, it's a binary 1. The data is in LSB order. The controller appears to send only 3 messages to the roaster. Turn the heat on/off and the duty cycle, Turn the fan on/off and the duty cycle, and turn the bean cooling fan on/off. Here are some examples of each function in the messages. The first byte is the fan speed, The third byte is the fan cooling speed, and the fifth byte is the heater. Code Download source 0x41, 0x04, 0x00, 0x64, 0x46, 0xEF - Roasting Power 70 Fan 65 The roaster sends temperature data in the first 4 bytes and a checksum in the 7th byte back to the controller.. There may be something else in there, too.. I'm not sure.. I haven't observed any correlation with the 5th and 6th bytes. They're almost always 0x00 and 0x01. Code Download source 0x3, 0xf9, 0x3, 0xc2, 0x0, 0x1, 0xc2 -- Temp 50F And this is the part I'm having trouble figuring out... If you look at the control board in the roaster, you'll see (as renatoa pointed out) they're using what appears to be a thermistor. It's being read with what I think is a voltage divider on the board.. but it's strange because instead of just one tap coming off it and going to an ADC pin on the microcontroller, they have two taps.. Each one goes through a resistor (one goes through a 2k Ohm resistor, one through a 1k Ohm resistor). I believe those values are what we see in the first and second pairs of bytes. There is an extremely strong correlation between the values of those bytes and the temperature shown on the screen. I can train a 3rd degree polynomial to predict the temp from those bytes and it is verrry close.. but the errors are still too far off.. sometimes up a degree, sometimes down two degrees, sometimes it'll be right on it.. I just can't seem to sort out the relationship between those bytes and the temp. I have a data set of about 1600 values for bytes 1,2,3,4 and the corresponding temperature shown on the screen. I collected that by capturing the data from the roaster using a logic analyzer, extracting the binary, then replaying each message back to the controller. I then record the value shown on the screen for each message. I think part of the reason my regression has the errors it has is because the controller is only showing me integer values so I'm losing some information there. I think I'm REALLY close to a logging solution, and I think a control solution could be implemented with a bit more effort. I think if you were going to control it externally, the way to go would be to just emulate the controller completely or just replace their controller with a TC4+.. I think you'd have to replace the thermistor with a thermocouple as well though. I've attached a file fullrealdataints.txt If anyone wants to take a crack at figuring out the relationship between the first two values (the first two bytes and the second two bytes converted to integers) and the last value (the temperature in Fahrenheit) then be my guest :) If you crack the code let me know.. This is the last hurdle to having logging implemented.
sloppyjosh attached the following file:
sloppyjosh attached the following images:
Edited by sloppyjosh on 12/03/2023 9:44 AM |
|
|
renatoa |
Posted on 12/03/2023 10:01 AM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
Great findings, you spent some time on this spy job ! So the protocol is a proprietary binary stream, not standard serial ? Did you figured if the temp values are proportional with voltage on the probe, or reversed? This could tell us the sensor type, RTD or NTC. The connection description, with two resistors, suggest me a differential input to ADC, as is used for a Pt100 adapter/amplifier, see attached image. An alternative to sending data elsewhere, would be keeping the whole self contained, by replacing the panel with a Raspi running Artisan, and a small piece of code as interface between the roaster protocol, and a known protocol for Artisan, TC4 or Modbus. Just a thought... ~~~
renatoa attached the following image:
Edited by renatoa on 12/03/2023 10:19 AM |
|
|
sloppyjosh |
Posted on 12/03/2023 12:33 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
The readings from the roaster are inversely proportional to the temps but I haven't put a meter directly on the probe. I used a 4th degree polynomial and got it working pretty well. I ran a preheat cycle and it the values output by my Arduino seemed in line with the controller. The controller applies some smoothing so it's kind of difficult to get a direct 1:1 agreement but it looked really good. I just need write the code to indicate the status of the fan and heater, put it in the correct format for Artisan and give it a go. |
|
|
renatoa |
Posted on 12/03/2023 1:41 PM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
You are moving faster than I can follow you ![]() Do you have any idea what processor is that... JS32... The other chip TM1640 is the displays driver, got it. |
|
|
sloppyjosh |
Posted on 12/03/2023 2:07 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
It's a js32t031f5s7 the data sheet is online.. in Chinese only.. Google translate works well on it though. The data lines are connected to the UART0 RX and TX lines but I think they must just be bit banging the output. That's how I drive the controller to correlate the values to the temp on the display. Unfortunately, the chip in the roaster doesn't appear to have any real identification on it. It says FMD N3hWIKH FMD is a chip manufacturer that makes a few microcontrollers but I couldn't find any data sheet that looked like it matched the chip itself.
sloppyjosh attached the following images:
Edited by sloppyjosh on 12/03/2023 2:17 PM |
|
|
sloppyjosh |
Posted on 12/04/2023 9:46 AM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Roasted 300g of Coffee Coral Ferdelance using profile 022 on the skywalker... Here's what I recorded in Artisan. The roast came out to about a City roast. With a loss of 12%. I usually like them into City+ or Full City.. Never had this blend before though so who knows.. maybe I'll like it. I have very little experience with artisan.. so I have no idea how this profile looks.. You tell me haha. That said.. My SkywalkerSpy works!
sloppyjosh attached the following image:
Edited by sloppyjosh on 12/04/2023 10:56 AM |
|
|
jwmelvin |
Posted on 12/04/2023 11:04 AM
|
![]() Newbie ![]() Posts: 10 Joined: December 21, 2022 |
This is great! Thank you for doing this work and sharing it here. It makes me much more likely to experiment with this roaster. |
|
|
renatoa |
Posted on 12/04/2023 1:20 PM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
It looks ok as is, close to the classic approach that advise having after dry end a continuous descending RoR (Delta BT), and avoid as much as possible flat areas (as minute 3 to 5), or even worse, a raising trend of the delta graph. Something like the red line I sketched on top of your graph. So the power reduction should start earlier, about minute 4, and be done in many smaller steps, at last two steps 70-60-50 instead the sharp 70-50 at 170C done by auto logic. Smaller steps for the fan too. Sky(walker) is the limit now for experiments. We have rules to know how many we broken when the last coffee we roast is memorable, and we are unable to reproduce the roast again ![]() Wondering how long will take until Darth Vader appears ...
renatoa attached the following image:
Edited by renatoa on 12/05/2023 3:31 AM |
|
|
sloppyjosh |
Posted on 12/04/2023 2:41 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Vader is on the way. ![]() I need to better understand how to get Artisan to talk to the Arduino. Currently, I have artisan calling a python program that asks the Arduino for the data. I don't think this approach will work for artisan to control it though. I believe you had mentioned using TC4 messages.. that may work.. If you have any other ideas/references for this let me know.. I don't really know artisan that well. |
|
|
jwmelvin |
Posted on 12/04/2023 10:03 PM
|
![]() Newbie ![]() Posts: 10 Joined: December 21, 2022 |
This may help understand how Artisan talks to a TC4: https://github.co...tisanQ_PID
Edited by renatoa on 12/05/2023 2:07 AM |
|
|
renatoa |
Posted on 12/05/2023 2:36 AM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
As @jwmelvin posted above, just an USB/serial stream implementing some of the TC4 commands, not all. The minimal set of commands should contain: READ, for data acquiring, and OT1/OT2 for HTR/FAN control. However, at the start of the roast Artisan sends some config commands, that could of interest for you to know how to tailor the READ command response packet. These commands are: - CHAN;2100 or CHAN;1200 - instructs you about the order of temperatures in the packet sent by you as reply to READ command. 1 means ET, 2 means BT For ET you can post same value as BT or zero. You should ack this command sending back #CHAN If not ack Artisan will continue spamming you with CHAN commands interlaced with READ commands. - UNITS; followed by C or F - this command tells to TC4 which unit will use Artisan, so all data sent as response to READ command should be converted by your box to C or F accordingly. This command should not be ack by sending back something - FILT;xx;yy;zz - this command immediately follows UNITS, you can ignore, is about filtering coefficients for rolling average of temperatures and rate of change. UNITS and FILT immediately follows #CHAN ack sent by you, and will never come back until they are changed in Artisan, next roast. They can't be changed in the middle of a roast. Response packet to a READ command looks like: AT;ET;BT;T3;T4;HTR;FAN;SP ; where - AT = ambient - ET/BT - could be reversed, according to CHAN command - T3/T4 = optional other two temperatures - HTR = actual heater value, to confirm the change by OT1 command - FAN = actual fan value, to confirm the change by OT2 command - SP = set point for a pid profile, ignore, set to zero Edited by renatoa on 12/05/2023 2:41 AM |
|
|
renatoa |
Posted on 12/05/2023 3:44 AM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
Quote This is line with to my roasts notes, beans looking as medium roast, but the weight loss is characteristic to a light roast... And they look not so well developed, beans are still smaller than I know them from a mixed convective-radiation roast. This could mean the IR is too powerful and penetrate only the surface, letting the inside less developed. Should experiment more with Manual mode, using lower power and longer roast times. And maybe more air. As is now, a roast done in the 6-7 minutes ballpark, looks like a fluid bed roast, minus the convection, thus somewhat forced, imo. |
|
|
Robotic Kitten |
Posted on 12/05/2023 3:57 PM
|
![]() Newbie ![]() Posts: 24 Joined: December 04, 2023 |
This thread needs more upvotes. Great job @sloppyjosh Quote just an USB/serial stream implementing some of the TC4 commands, not all. Are there any BLE roasters which Artisan supports? I wouldn't mind a wireless connection to the roaster ![]() |
|
|
sloppyjosh |
Posted on 12/05/2023 4:50 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Full control is working. Haven't done a roast yet but I was playing with the PID controller just for fun. There's still a few quirks to work out but overall I'm pleased with it.
sloppyjosh attached the following image:
|
|
|
Robotic Kitten |
Posted on 12/05/2023 5:37 PM
|
![]() Newbie ![]() Posts: 24 Joined: December 04, 2023 |
Quote sloppyjosh wrote: Code Download source 0x3, 0xf9, 0x3, 0xc2, 0x0, 0x1, 0xc2 -- Temp 50F And this is the part I'm having trouble figuring out... If you look at the control board in the roaster, you'll see (as renatoa pointed out) they're using what appears to be a thermistor. It's being read with what I think is a voltage divider on the board.. but it's strange because instead of just one tap coming off it and going to an ADC pin on the microcontroller, they have two taps.. Each one goes through a resistor (one goes through a 2k Ohm resistor, one through a 1k Ohm resistor). Any chance you could post the full picture of the board and indicate where the "thermistor" is connected to? Can you also confirm if the thermistor resistance increases or decreases with the temperature? One hypothesis: it is an Negative Temperature Coefficient thermistor and voltage divider is: 5v -- R1 -- Thermistor -- R2 -- GND and the two taps are connected to thermistor's terminals. Then the 1st integer is an ADC value for R1/Thermistor tap and the second value is Thermistor/R2 tap (closer to the ground). The higher the temp -> the lower thermistor's value -> the lower both taps and closer to each other in value. Edited by Robotic Kitten on 12/05/2023 6:08 PM |
|
|
sloppyjosh |
Posted on 12/05/2023 6:44 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Here's a close up of the board. The thermistor is the two connections by the blue arrow. I believe the orange connection has a filter cap (C5) between the line and ground. I still haven't taken the board back out to check the thermistor resistance. I'll try to do that tomorrow.
sloppyjosh attached the following image:
|
|
|
sloppyjosh |
Posted on 12/05/2023 11:56 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Code is here: https://github.co...kerRoaster |
|
|
renatoa |
Posted on 12/06/2023 1:08 AM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
Quote Robotic Kitten wrote: This thread needs more upvotes. Great job @sloppyjosh Quote just an USB/serial stream implementing some of the TC4 commands, not all. Are there any BLE roasters which Artisan supports? I wouldn't mind a wireless connection to the roaster ![]() Depends if the BLE on the device running Artisan implements BT serial. |
|
|
renatoa |
Posted on 12/06/2023 10:58 AM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
From github project Quote For the Fan and Heater, duty cycles increment by 5. Sending other values will be ignored. So I can't have 1% control heater precision using the protocol ? If I send 48% will be ignored ? Either 45 or 50, nothing inbetween ? |
|
|
renatoa |
Posted on 12/06/2023 11:42 AM
|
![]() Administrator ![]() Posts: 3131 Joined: September 30, 2016 |
Quote Robotic Kitten wrote: One hypothesis: it is an Negative Temperature Coefficient thermistor and voltage divider is: 5v -- R1 -- Thermistor -- R2 -- GND and the two taps are connected to thermistor's terminals. Then the 1st integer is an ADC value for R1/Thermistor tap and the second value is Thermistor/R2 tap (closer to the ground). The higher the temp -> the lower thermistor's value -> the lower both taps and closer to each other in value. The divider is 5V -> R15 (30k) / NTC (5k) - Gnd. Thus, the voltage on NTC should be about 5V * 5k / (30k+5k) = 0.7V ballpark, at ambient temp. If this voltage is measured by a 12 bit ADC (0...4095), corresponding to a 3.3V input voltage range, then the ADC value of 0,7V would be 887, somewhere in the dataset post by sloppyjosh. The two resistors coming from the processor, R25 and R16, both connects to the NTC common point of divider. No idea what could be measured on two separate paths, connected to same point... Maybe one path is connected by other trace to other onboard sensor, to implement an ambient temperature compensation. Plotting the sloppyjosh data, we have that attached graph. The gray curve is the display temperature. The other two plots looks both as different parts of a typical NTC graph, as seen in the "Linearization..." picture, which is a plot based on Steinhart Hart_equation: https://en.wikipe...t_equation An Arduino library implementing this equation could be found here: https://github.co...thermistor There are three parameters needed: Nominal resistance at 25 ºC (~5k), thermistor's beta coefficient, Value of the series resistor (30k). The unknown is the beta coefficient, I think can be found by reverse eng from the sloppyjosh data. ~~~
renatoa attached the following images:
Edited by renatoa on 12/06/2023 12:33 PM |
|
|
Robotic Kitten |
Posted on 12/06/2023 5:04 PM
|
![]() Newbie ![]() Posts: 24 Joined: December 04, 2023 |
Quote Thanks for the great writeup! |
|
|
sloppyjosh |
Posted on 12/06/2023 6:51 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Quote No problem! I'm just over here having fun ![]() |
|
|
sloppyjosh |
Posted on 12/06/2023 9:18 PM
|
![]() Newbie ![]() Posts: 30 Joined: December 01, 2023 |
Quote renatoa wrote: Quote Robotic Kitten wrote: One hypothesis: it is an Negative Temperature Coefficient thermistor and voltage divider is: 5v -- R1 -- Thermistor -- R2 -- GND and the two taps are connected to thermistor's terminals. Then the 1st integer is an ADC value for R1/Thermistor tap and the second value is Thermistor/R2 tap (closer to the ground). The higher the temp -> the lower thermistor's value -> the lower both taps and closer to each other in value. The divider is 5V -> R15 (30k) / NTC (5k) - Gnd. Thus, the voltage on NTC should be about 5V * 5k / (30k+5k) = 0.7V ballpark, at ambient temp. If this voltage is measured by a 12 bit ADC (0...4095), corresponding to a 3.3V input voltage range, then the ADC value of 0,7V would be 887, somewhere in the dataset post by sloppyjosh. The two resistors coming from the processor, R25 and R16, both connects to the NTC common point of divider. No idea what could be measured on two separate paths, connected to same point... Maybe one path is connected by other trace to other onboard sensor, to implement an ambient temperature compensation. Plotting the sloppyjosh data, we have that attached graph. The gray curve is the display temperature. The other two plots looks both as different parts of a typical NTC graph, as seen in the "Linearization..." picture, which is a plot based on Steinhart Hart_equation: https://en.wikipe...t_equation An Arduino library implementing this equation could be found here: https://github.co...thermistor There are three parameters needed: Nominal resistance at 25 ºC (~5k), thermistor's beta coefficient, Value of the series resistor (30k). The unknown is the beta coefficient, I think can be found by reverse eng from the sloppyjosh data. ~~~ I believe it's using 10-bit ADCs, all the values are within that range. Additionally, the temps we see are derived from both the values sent in the data. It's not just ignoring one, or one is something else we don't understand, or a completely different sensor, etc.. I have another script for replaying values to the controller to see what the temp will display. Through manual experimentation you can immediately tell both values are used to derive the temp. When you sort the data by the values of either the first or second column, you can see what I mean. Consider these rows, they all have the same value for the first.. 1011 Code Download source 1011,820, 102 But now we can sort by the second row and see the same thing. All with 2nd value 29. Code Download source 309 29 410 This occurs at low temps for the first value, and high temps for the second one.. Of course, these may not be the raw values from the ADC.. maybe they've been transformed somehow. but it just doesn't make sense. Quote So I can't have 1% control heater precision using the protocol ? If I send 48% will be ignored ? Either 45 or 50, nothing inbetween ? This is correct. I tested by setting something low like 25 then going to 78. Nothing happens. But if you go to 75 you'll see the heater get brighter. I was thinking about collecting another set of data.. I need to do it anyway.. at least for some higher temps beyond what's in the data set.. The model is very much overfit to the dataset and won't generalize well.. if you go beyond, say 435F things are going to get strange really fast. But I was considering putting a second probe inside the machine and logging the real temp reported by that probe. Maybe even running a roast with it like this, too. I have a few probes, but would probably use the bare thermocouple as I think it'd have the fastest response time. I would expect the Skywalker's probe would lag behind just a bit in comparison but I'm curious to see what it would look like. I find it interesting that on the two roasts I've done in it, I hit FC about 20 degrees too soon. Edited by sloppyjosh on 12/06/2023 10:17 PM |
|
Jump to Forum: |