Who is here? 1 guest(s)
 Print Thread
TC4 - Overview and announcements
JimG
I am open to other ideas, too.

But awhile back I created a series of threads related to the TC4 that I hoped would provide homes for most discussions:
http://forum.home...rum_id=133

Of course, none of them are "official." ;)

Jim
 
farmroast
I started a "TC4 Users" thread a little time back.
http://forum.home...ad_id=2383
My thought was if we talk about how we use the various setups it would help new interests sort through what they might need/want.
Edited by farmroast on 12/15/2011 10:19 AM
Ed B.
DreamRoast 1kg roaster, Levers, Hand Mills http://coffee-roa...gspot.com/
 
JimG
This is to announce the availability of a new LCD option that was designed specifically for the TC4C standalone board.

The new adapter, the LCDapterC, is also fully compatible with the TC4 shields.

The new wrinkle on the LCDapterC is that it optionally can be mounted directly on the TC4C using 3 standoffs, making a nice unit for panel mounting inside a project box. The position of the I2C pins on the new LCDapterC matches the I2C header on the TC4C. So by mounting a 4 x 1 female socket on the LCDapterC, no cable is required to enable the use of a character LCD.

Photo below shows how the new LCDapterC (with a 16x2 LCD and some buttons already mounted) can be connected to the TC4C. When connected together, there are 4 accessible holes intended for panel mounting.

Jim
JimG attached the following image:
stacked.jpg

Edited by JimG on 12/19/2011 8:31 AM
 
JimG
Arduino 1.0 Compatibility

The standard TC4 libraries, aArtisan, aBourbon, and aCataui are now compatible with the new Arduino 1.0 release.

The revised TC4 standard library download is required for any TC4 application using Arduino 1.0. You may download it here:
http://code.googl...n=2&q=

aArtisan version 2.00 may be downloaded here:
http://code.googl...n=2&q=

aBourbon version 3.00 may be downloaded here:
http://code.googl...n=2&q=

aCatuai version 2.00 may be downloaded here:
http://code.googl...n=2&q=

Jim
Edited by JimG on 01/26/2012 11:09 PM
 
JimG
So, you need to read 8 thermocouples?

I had a chance to work on a mini-project today. A TC4C user wrote and said reading only 4 thermocouples was no longer getting the job done, and that he wanted to read up to 4 more. How to do this inexpensively?

Turned out to be surprisingly easy:

1. Build a stripped down TC4 shield (4 screw terminals, MCP3424 chip, 2 capacitors, and the 4-pin I2C header).

2. Carefully bend up pin no. 10 (Adr1) on the MCP3424.

3. Solder the remaining 13 pins of the ADC to the TC4 shield.

4. Connect the stripped down TC4 to either a TC4C board, or to a TC4/Arduino combination, using a 4-wire I2C cable.

5. Use 0x69 for the I2C address of the extra MCP3424.

Of course, there will be a little programming needed to access all 8 channels. But fundamentally all that is needed is to introduce a second ADC object, initialize it to 0x69 (the default is 0x68 for the basic TC4 system), and then use the basic skeleton of any of the existing TC4 applications.

Jim
 
bvwelch
8 channels -- very cool Jim! -bill
 
Coffee makes the world goround
So,, Last year around Xmas i did buy a Tc4C m and had it shipped to me (Denmark)

had it tested on a friends super computer , and it did work fine

Things got in the way and first now i did try it on a old laptop i got cheap (dead battery)

I have Artisan
and the Tc4C came pree programmed with aArtisan and was allready tested

but i cant get it to work on my laptop

Artisan runs , but no readings fro the temp probes

i think i am missing a driver for the Tc4C ?? could this be so ??

and wil my laptop be usefull at all ??

Laptop is a Compaq Evo
Windows xp
Mobile intel Pentium
4-M cpu 2,00GHz
1,2 GHz 768 MB ram

or would i be better of using a different logging program ( then i would need a different programming of the Tc4C i know )
 
greencardigan
Have you checked the settings in the 'Config' menu in Artisan?

You need to check the device section and have it set for TC4.

And also check the serial port settings. Check that the appropriate COM port for your TC4C is selected and baud 19200, byte size 8, Parity N, Stopbits 1.
 
Coffee makes the world goround

Quote

greencardigan wrote:

Have you checked the settings in the 'Config' menu in Artisan?

You need to check the device section and have it set for TC4.

And also check the serial port settings. Check that the appropriate COM port for your TC4C is selected and baud 19200, byte size 8, Parity N, Stopbits 1.


check check check
all settings was like you write

isnt there any need for a driver for the Tc4C
if i remember correcty , my computer guru friend DID download something aside from Artisan
 
greencardigan
I dont remember needing any drivers. Are you getting a serial port appearing in windows device manager when you plug the TC4C in?

Is the TC4C powering on? Do you have a LCD connected?
 
greencardigan
Actually have a read here.

http://arduino.cc...sWindowsXP

And I attached two files from my drivers directory. I'm not sure which one is required for the TC4C.
 
Coffee makes the world goround
The first couple of times i connected the Tc4C , the cumputer did say it needed a driver for FT232 USB UART

i did find one on the net , , and thought is was installed
the Tc4c is powering up (the green led is on ) and the cumputer makes a noise when you connect it , but it dont ask for a driver anymore , but with my best computer duumynes , i did check and it says no driver is installed for the FT232 USB UART device ???
 
JimG
To be sure you have the correct and latest drivers for the FTDI USB-serial chip, use this link:
http://www.ftdich...rs/VCP.htm

(I recommend using the virtual com port (VCP) drivers, and not the D2XX drivers, BTW).

Jim
 
Coffee makes the world goround

Quote

JimG wrote:

To be sure you have the correct and latest drivers for the FTDI USB-serial chip, use this link:
http://www.ftdich...rs/VCP.htm

(I recommend using the virtual com port (VCP) drivers, and not the D2XX drivers, BTW).

Jim


To greencardigan

thanks fot the link . looks like i am not alone with problems like that

Jim , i had allready been to that site ,AND dowloaded the newest version
didnt work

but sins i had it open again (clicked your link) i did try to use the old unsurported version

and that did the trick best post

Now i can use Artisan

it behaves strange if you only have one probe , even when in the settings you set it to only one channal

it shows two temps , one for et and one for beens , they both change if you heat the one and only probe , but not the same the curves split apart , and then sloooowly come together again ???



Luckily when using two probes ,,,,no problems only a slight ofset (5 degreeC to high)

that can be the probes , and as long as its allways the same dosnt matter

my laptop is working slowly
the longer logging time , the slower it goes

have some here tested it using ubunto
Edited by Coffee makes the world goround on 09/26/2012 8:04 PM
 
greencardigan
If you're only using one probe then I think you should use a bit of wire to connect the terminals of the other channel together.

Setting Artisan to do read intervals of 2 second instead of 1 second might help to stop it slowing down.
 
Coffee makes the world goround
I have several roasters ( no I AM NOT ADICTED ;;;NO WAY :300ccCoffee.gif:BBQ grillsmiley-hot.gifsmile

and most if not all can use 2 or more probes

When i once build a 500gram drum roaster
i going to need all 4 channels

temp outside drum
Temp inside drum
Temp in bean mass
temp in exhaust
 
georgel

Quote

JimG wrote:

This is to announce the availability of a new LCD option that was designed specifically for the TC4C standalone board.

The new adapter, the LCDapterC, is also fully compatible with the TC4 shields.

The new wrinkle on the LCDapterC is that it optionally can be mounted directly on the TC4C using 3 standoffs, making a nice unit for panel mounting inside a project box. The position of the I2C pins on the new LCDapterC matches the I2C header on the TC4C. So by mounting a 4 x 1 female socket on the LCDapterC, no cable is required to enable the use of a character LCD.

Photo below shows how the new LCDapterC (with a 16x2 LCD and some buttons already mounted) can be connected to the TC4C. When connected together, there are 4 accessible holes intended for panel mounting.

Jim


This seems to be what would work for me. altho I am a bit fuzzy as to which of the programs I might want to have preloaded. My best use would be with my Smoker and I may also figure a way to use some control + data logging on my modified Ronco coffee roaster. However I am not sure what and how to order. You mentioned roastlogger on your pm but I don't see it in the datalogger thread.
georgel
]
 
Barrie

Quote

JimG wrote:

Starting in early October, all of the TC4 pre-populated boards I've mailed out to people have been / will be pre-initialized with default identification and calibration values in the TC4's EEPROM. This will spare folks from needing to run the writeCal.pde sketch on their new SMD-populated boards.

I am also performing a small suite of tests on the temperature sensor, ADC, LED's, and output transistors on the SMD-populated boards before they are mailed. Fortunately, there haven't been any instances of bad chips on the SMD pre-populated boards reported to me, but this extra step should virtually eliminate the odds of that happening.

(I built a testing jig using a Freeduino board and a few pogo pins. PM me if you are interested in the details.)

Jim


With Jim away, I wonder if someone else can speak to the calibration issues? I installed the HTC/TC4 combo and, at first, used it just for logging with an inexpensive probe through the chute. This worked very well, with 1C usually at around 400. Flushed with success the next step was to go the whole nine yards with bean and environmental probes through the rear wall etc. The (upgraded) probes are Omega XCIB-K-3-5-3s. This works entirely as intended, with one exception. 1C now usually occurs at 370, according to the T1 probe! Everything else looks perfect, with the environmental and bean temp/time curves exactly as they should be, if one just ignores the numbers. I could live with this situation but for the fact that I went for top-of-the-line probes with an expectation of reliability and accuracy. I wonder about calibration at the pcb/software level but then remember that the previously-used el cheapo probe gave the "right" numbers. It is very unlikely that Omega sent out probes with faulty performance. Each is checked pre-shipping. Unfortunately they are now JB Welded to the rear wall and related sleeves.
Barrie attached the following image:
image_42.jpg

Edited by Barrie on 09/21/2013 7:33 PM
Barrie (San Diego, CA)
"So much to learn, so little time."
Hottop 2K+., Artisan, Jura Capresso ENA 3 (i.e. espresso).
 
JackH
I don't know much about the HotTop, but when I run my turbo roaster empty, BT and ET are usually about the same temperature once it warms up. Something to check.

Also, the 370 seems more like 1C to me. My 1C is usually around 370-380F. Maybe your old probe was inaccurate or the location it was mounted is different.
---Jack

KKTO Roaster.
 
allenb
Jack's recommendation to check one against the other with no beans is the best way to know if the omega bean probe is off.

It's interesting how finicky bean temp probes can be. On my 1 lb easydrum I've used two different locations not very far from each other and two totally different readings at 1C. 400 F at the first location which I'm used to seeing in my fluidbed roasters and the current location reads 387 at 1C. I guess the closer we can get to 380F for a bean temp at 1C the closer we are to the actual internal bean temperature.

Allen
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
Barrie

Quote

JackH wrote:

I don't know much about the HotTop, but when I run my turbo roaster empty, BT and ET are usually about the same temperature once it warms up. Something to check.

Also, the 370 seems more like 1C to me. My 1C is usually around 370-380F. Maybe your old probe was inaccurate or the location it was mounted is different.


At ambient temperature, both read the same correct temp.
Barrie (San Diego, CA)
"So much to learn, so little time."
Hottop 2K+., Artisan, Jura Capresso ENA 3 (i.e. espresso).
 
Barrie

Quote

allenb wrote:

Jack's recommendation to check one against the other with no beans is the best way to know if the omega bean probe is off.

It's interesting how finicky bean temp probes can be. On my 1 lb easydrum I've used two different locations not very far from each other and two totally different readings at 1C. 400 F at the first location which I'm used to seeing in my fluidbed roasters and the current location reads 387 at 1C. I guess the closer we can get to 380F for a bean temp at 1C the closer we are to the actual internal bean temperature.

Allen


I would love to talk myself into the belief that what I have is a highly-accurate "correct" temperature. cross fingers
Barrie (San Diego, CA)
"So much to learn, so little time."
Hottop 2K+., Artisan, Jura Capresso ENA 3 (i.e. espresso).
 
rgrosz78

Quote

Barrie wrote:With Jim away, I wonder if someone else can speak to the calibration issues? I installed the HTC/TC4 combo and, at first, used it just for logging with an inexpensive probe through the chute. This worked very well, with 1C usually at around 400. Flushed with success the next step was to go the whole nine yards with bean and environmental probes through the rear wall etc. The (upgraded) probes are Omega XCIB-K-3-5-3s. This works entirely as intended, with one exception. 1C now usually occurs at 370, according to the T1 probe! Everything else looks perfect, with the environmental and bean temp/time curves exactly as they should be, if one just ignores the numbers.

Barrie, sorry for the slow reply ... I recently installed ET/BT thermocouples in my Hottop using the exact same Omega hardware. I can confirm that my readings are similar to what you are seeing. My 1st crack typically occurs between 360 and 370, which is lower than results from other thermocouples used by other home roasters.
rgrosz78 attached the following image:
mexican_alturas_chiapas_2012_fto.png

Life is too short to drink bad wine ... or bad coffee!
 
Barrie
That is so good to know, and very reassuring. I have considerable confidence in the Omega brand but have been kicking myself that I did not at least try them in boiling water before installation complete with JB Weld. thumbdown

I am using Roast Logger which serves my purpose pretty well, but your chart looks very pretty. What software are you using?
Barrie attached the following image:
image_43.jpg

Edited by Barrie on 09/28/2013 10:38 AM
Barrie (San Diego, CA)
"So much to learn, so little time."
Hottop 2K+., Artisan, Jura Capresso ENA 3 (i.e. espresso).
 
rgrosz78
I use the Artisan Roaster Scope software, as discussed here:
http://homeroaste...owstart=60
Life is too short to drink bad wine ... or bad coffee!
 
Jump to Forum: